Packed Cylinder Safety

2545 days ago, 763 views
PowerPoint PPT Presentation
. Subject to damagefrom different exercises inthe region. Chamber laying in a horizontalposition.. Electrical string inContact with thecylinder. . Barrels are not shielded from falling. Notethat the Chain is not secured over.. . Chain. Chamber not secured. 2. Barrel ought to be put away. 3. Subject to harm..

Presentation Transcript

Slide 1

Compacted Cylinder Safety NCMAQB

Slide 2

Subject to harm from different exercises in the region Electrical rope in Contact with the chamber Cylinder laying in a flat position.

Slide 3

Chain Cylinders are not shielded from falling. Take note of that the Chain is not secured over.

Slide 4

Electrical Cord Cylinder not secured 2. Chamber ought to be put away 3. Subject to harm. 4. Electrical rope hung over.

Slide 5

1. Little chamber not tied off 2. Combustibles put away with barrels 3. Terrible housekeeping 4. Acetylene and Oxygen put away excessively near one another and no chain.

Slide 6

1. Chamber with no valve or top introduced 2. Laying even on the ground 3. Subject to harm

Slide 7

Electrical circular segment harm Cylinder is harmed. Ought to be removed from administration promptly!

Slide 8

Cylinder ought to be away shielded from harm and not laying on the ground in any case in the event that it is full or discharge

Slide 9

Forklift 1. Chambers laying on the ground and dishonorably put away 2. Subject to harm from forklift operation in region

Slide 10

1. Sustain line presented to harm/release that could bring about a fire/blast 2. Stumbling Hazard

Slide 11

1. Deficient housekeeping 2. Valve tops ought to be introduced.

Slide 12

Acetylene Cylinder Unsecured acetylene chamber 2. Presented to harm

Slide 13

Unsecured chambers

Slide 14

Regulator left pressurized after utilize

Slide 15

Improper Storage

Slide 16

Tie Off?

Slide 17

Cylinders not Secured legitimately

Slide 18

Free standing barrels Exposed to harm From development Activities in region

Slide 19

What a pressurized Container can do When the perfect measure of warmth is connected.

Slide 20

How not to explode yourself Or, the significance of utilizing flashback arrestors on oxy-acetylene trucks and keeping sparkle delivering exercises Away From You (min 35 ft.) .

Slide 21

An Ironworker group was changing a brief basic steel connect utilizing an Oxygen/Acetylene burn setup on a truck, a compact welder, and a processor. Obviously the Acetylene hose built up a hole and touched off amid the granulating operation ( Monday June 18, 2001 )

Slide 22

The light setup was not outfitted with a "flashback" arrestor check valve and the fire went through the hose into the compacted barrel. All Oxygen/Acetylene setups must have a "Flashback" arrestor check valve at the controllers, NOT the light head, to keep this sort of event. This little gadget would have kept this fire.

Slide 23

30 CFR § 56.4600 Extinguishing gear. WELDING/CUTTING/COMPRESSED Gasses (a) When welding, cutting, patching, defrosting, or bowing (1) With an electric curve or with an open fire where an electrically conductive stifling operator could make an electrical risk, a multipurpose dry-substance fire douser or other quencher with no less than a 2-A:10-B:C rating might be at the worksite. (2) With an open fire in a range where no electrical risk exists, a multipurpose dry-compound fire douser or proportional fire stifling hardware for the class of flame peril show should be at the worksite.

Slide 24

30 CFR § 56.4601 Oxygen barrel stockpiling. Oxygen barrels should not be put away in rooms or territories utilized or assigned for capacity of combustible or burnable fluids, including oil.

Slide 25

30 CFR § 56.4602 Gages and controllers. Gages and controllers utilized with oxygen or acetylene chambers should be kept spotless and free of oil and oil.

Slide 26

30 CFR § 56.4603 Closure of valves. To keep unintentional arrival of gasses from hoses and lights connected to oxygen and acetylene chambers or to complex frameworks, barrel or complex framework valves should be shut when (a) The barrels are moved; (b) The light and hoses are left unattended; or (c) The errand or arrangement of assignments is finished.

Slide 27

30 CFR § 56.15007 Protective hardware or attire for welding, cutting, or working with liquid metal. Defensive dress or gear and face shields, or goggles might be worn when welding, cutting, or working with liquid metal.

Slide 28

30 CFR § 56.16005 Securing gas chambers. Compacted and fluid gas chambers should be secured in a sheltered way.

Slide 29

30 CFR § 56.16006 Protection of gas chamber valves. Valves on compacted gas chambers might be secured by spreads while being transported or put away, and by a protected area when the barrels are being used.