IC91AD Programming

1800 days ago, 1003 views
PowerPoint PPT Presentation

Presentation Transcript

Slide 1

IC91AD Programming

Slide 2

IC91AD Programming There are a few approaches to store data into the IC91. You can physically compose channel data utilizing the front board. This is extremely dreary and blunder inclined and not prescribed unless you simply need to store maybe a couple channels. Icom offers their copyrighted RS91 Cloning Software that uses a basic link and PC interface. Dan Smith, KK7DS offers an allowed to download cloning bundle called CHIRP that uses an indistinguishable link from the RS91 bundle.

Slide 3

IC91/IC2820 Cloning Cable

Slide 4

IC91AD - CHIRP http://chirp.danplanet.com/download/Development of CHIRP is done in my extra time and is offered as open-source programming, for nothing out of pocket. On the off chance that you like CHIRP, please think about contributing as a little gift to bolster the expenses of advancement and equipment. Dan Smith KK7DS There is a PayPal interface on Dan's Page.

Slide 5

IC91AD - Manual Programming Band - A Chapter 4 in your IC91AD client manual blueprints manual programming. The IC91 is separated into two groups or VFOs, An and B, or Main and Sub Band. The A Band contains 800 Memory Channels that might be separated into 26 Banks. The A Band bolsters FM (20 kHz. channels), WFM (Wide FM 150 kHz channels) and AM, getting from 495 kHz to 999.990 mHz. - NOTE – NO DSTAR in the A BAND. Transmit is constrained to FCC Band Allocations.

Slide 6

IC91AD - Manual Programming Band - B The B Band contains 400 Memory Channels that might be isolated into 26 Banks. The B Band bolsters FM (20 kHz. channels), NFM (Narrow FM 12.5 kHz. channels) AM and DV (DSTAR), accepting two sections from 118 mHz. to 174 mHz. furthermore, 370 mHz. To 470 mHz. NOTE - DSTAR is in the B BAND as it were. Transmit is constrained to FCC Band Allocations.

Slide 7

IC-91 Keyboard Press catches on the substance of the IC-91 do numerous undertakings. Every key has a few distinct names. The RED marks show squeezing immediately. The BLACK marks demonstrate press and hold for two seconds. The console additionally produces DTMF or Touchtones amid transmit and numeric contribution for recurrence passage or channel number.

Slide 8

IC-91 Keyboard - MENU/LOCK The MAIN/DUAL key immediately flips amongst An and B Band VFOs. Press and Hold the MAIN/DUAL Key and you go from Single to Dual band gathering. The MENU/LOCK key immediately flips amongst Menu and Operate modes. Press and Hold the MENU/LOCK key to LOCK the console. A little KEY symbol is shown in the upper right corner of the show to demonstrate Key Lock.

Slide 9

IC-91 Keyboard - A Menu The MENU Items contrast between the An and B BANDS. The MENU in the A BAND offers: 1 - SET MODE 2 - SCAN 3 - DUP/TONE 4 - DISPLAY SOUNDS The UP/DOWN/LEFT and RIGHT bolt keys are utilized to explore through the menus, and the 5 Key with the ENTER sysbol is utilized to WRITE information.

Slide 10

IC-91 Keyboard - An or B Band Menus - SET MODE page 1. AP OFF - Turns the Radio OFF after a settled time. A little check symbol is shown in the upper right of the screen to demonstrate clock operation. Control Save - Momentarily controls the radio off for a brief span at occasional interims to enhance battery life. Attenuator - Reduces Receive Sensitivity to diminish impedance.

Slide 11

IC-91 Keyboard - An or B Band Menus - SET MODE page 2. Screen - Sets the screen key for Momentary or Toggle initiation – Monitor listens to your transmit recurrence. Dial Speed Up - Accelerates the turning dial activity. Auto Rpt - Automatically sets transmit counterbalance in light of the band portion and the Offset modified in the DUP/TONE Offset menu.

Slide 12

IC-91 Keyboard - An or B Band Menus - SET MODE page 3. MIC Simple - Sets how the HM-175 Spk/Mic works. Climate Alert - Causes the radio to filter the WX channel and sound ready tones when NOAA communicates extreme climate alarms. AP ON - Automatically turns the radio ON after a settled OFF time.

Slide 13

IC-91 Keyboard - An or B Band Menus - SET MODE page 4. Bolt - Sets whether to bolt all keys or bar volume or squelch controls. PTT Lock - Sets whether to incorporate PTT in the Lock setting. Occupied Lockout - Prevents transmission when the radio is un-squelched or accepting a call.

Slide 14

IC-91 Keyboard - An or B Band Menus - SET MODE page 5. TOT – Limits Transmit ON time in case of a stuck receiver. Dynamic Band – Single/All - In the VFO mode, when utilizing the channel selector to propel recurrence, SINGLE keeps the VFO in one band or scope of frequencies, for example, the 2M band. ALL lets the VFO cross band limits.

Slide 15

IC-91 Keyboard - An or B Band Menus - SCAN - page 1. Need Watch – ON, OFF, BELL – Interrupts brings in advance to check for approaches the PRIORITY channel and can sound an alarm – Bell – when there is movement on the need channel. Need Watch flips between the VFO and either a Call channel, or a Memory Channel, or Bank Scan of Memory Channels. Need Watch works in either Band An or B, yet not both in the meantime.

Slide 16

IC-91 Keyboard - An or B Band Menus - SCAN - page 2. Stop – Sets hang time when there is movement on a channel – differs from 2 seconds up to holding for the length of the call. Continue – Sets to what extent the radio will stay on a channel being filtered after the call closes. Ranges from 0 seconds to uncertain hold. Bank Link – Sets which and what number of banks will be filtered.

Slide 17

IC-91 Keyboard - An or B Band Menus - Duplex/Tone page 1. Counterbalanced Frequency – Sets the Repeater Offset utilized as a part of the 2 Meter Band. Repeater Tone – Sets the Sub Audible tone used to get to a repeater. CTCSS Tone – Sets the Sub Audible tone utilized by the radio beneficiary to square meddling signs.

Slide 18

IC-91 Keyboard - An or B Band Menus - Duplex/Tone page 2. DTCS Code - The Digital Squelch Code used to get to a computerized coded squelch get to repeater. DTCS Polarity – Sets whether information bits bringing on a positive move in recurrence are zero or one bits. DTMF Speed – Sets the term of DTMF tones utilized as a part of autopatch and control capacities.

Slide 19

IC-91 Keyboard – An or B Band Menus - DISPLAY page 1. Backdrop illumination – ON, OFF, AUTO, On Continuously. OFF and Automatically turns on for a few moments subsequent to changing a setting. Occupied LED – ON, OFF – Indicates movement on the radio channel. LCD Contrast – Sets the screen differentiate for best perceivability.

Slide 20

IC-91 Keyboard – An or B Band Menus - DISPLAY page 2. Check Name – ON/OFF – Displays the name of the Programmed Scan List or Bank Name. Opening LOGO – Displays ICOM IC-91 - ON/OFF. Opening Call Sign – Displays MY CALL on catalyst - ON/OFF. Text dimension – Sets Small or Large show textual style.

Slide 21

IC-91 Keyboard – An or B Band Menus - SOUNDS page 1. Beep Level – Sets the Loudness of Beep Tones. Key Touch Beep – ON/OFF – Sets Key Touch Beep. Examine Stop Beep – ON/OFF – Sets Beep on Scan Stop

Slide 22

IC-91 Keyboard - An or B Band Menus - Sounds page 2. Scope AF – Turns Speaker ON/OFF amid band clear. Volume Select – Combines or Separates tumult setting for An and B Bands. Standby Beep – In DV Mode causes a beep when the sending station quits sending or the flag blurs.

Slide 23

IC-91 Keyboard – B Band Menus 1 – Call Sign 2 – Received Call Sign 3 – Message/Position 4 – DV Voice Memo 5 – Set Mode 6 – DV Set Mode 7 – SCAN 8 – Duplex/Tone 9 – Display 10 – Sounds

Slide 24

IC-91 Keyboard - B Band Menus page 1 - Call Sign – Sets UR, RPT1, RPT2, and MY. Permits picking pre-modified call signs put away in the UR or Repeater call recollections. 2 - RX Call Sign – Displays a rundown of as of late got DSTAR Call Signs.

Slide 25

IC-91 Keyboard – B Band Menus page 2. 3 - Message/Position 3a - Transmit Message – Displays the 20 Character message to be sent. 3b - Received Message – Displays the Received 20 character message. 3c - GPS – Sets TX String 3d - Received GPS – Displays Received String 3e - Position – Displays MY Position and the Received Stations Position.

Slide 26

IC-91 Keyboard - B Band Menus page 3. 4 - DV Voice Memo – Track 1, 2 or 3 Selects the Recording Track for recording approaching voice. Answer Voice Records and Plays Back your Auto Reply Message. Track Size sets the message length for approaching message recording. 5 - Set Mode – The SET MODE in An and B are the same and either sets BOTH.

Slide 27

IC-91 Keyboard – B Band Menus DV SET MODE page 1. 6 – DV Set Mode 6a – Auto Reply 6b – Digital Code 6c – DV Data Transmit 6d – Digital Monitor 6e – Digital Repeater Set 6f – Received Call Sign Write 6g – Received Repeater Call Sign Write 6h – GPS Mode – OFF/ON 6i – GPS Auto Transmit Interval 6j – Auto Detect DV Transmissions 6k – Edit Records

Slide 28

IC-91 Keyboard – B Band Menus DV SET MODE page 2. 6a – Auto Reply – OFF/ON/Voice. Whenever set and your radio gets a call coordinated to your call sign or Digital Group Code (CSS or DCS), where UR=MY CALL, the IC-91 can be set to consequently answer with your TX Message and a short Voice Message.

Slide 29

IC-91 Keyboard – B Band Menus DV SET MODE page 3. 6b – Digital Code – Sets a 2 digit numerical code for specific gathering calling. This permits radios to stay quieted until a call is coordinated to a particular gathering number or call sign. 6c – DV Data Transmit – PTT/AUTO - The 1200 baud information port on the IC-91 sends serial information interleaved with the advanced voice data. This setting figures out if the information is sent on PTT or naturally.

Slide 30

IC-91 Keyboard – B Band Menus DV SET MODE page 4. 6d – Digital Monitor – Auto/Digital/Analog – Sets how the collector distinguishes motions in the DV mode when the squelch catch is squeezed. 6e – Digital Repeater Set – ON/OFF Automatically "STORES" the repeater's Call Sign when your radio is not modified accurately to your repeater's call sign.

Slide 31